Taking care of your model engines, whether they are two or four strokes, is the easiest way to ensure a long enjoyable operating lifespan for them. Here we will give you a few tips on just how to keep your little gem performing . . .

Day-to-Day Maintenance

There are three basic steps one should take on a day-to-day basis to ensure you continue getting the most from your engine:

1. Keep your engine clean on both the inside and outside. By keeping pariticles of dirt out of the workings of your engine, the operating surfaces will remain smooth and therefore less wear and better performance will result. Always use a fuel filter between your tank and the engine to catch any particles in the fuel. When operating in dusty conditions, use an air filter on your carb to keep particles out of your air intake. When done for the day, use a motor spray to clean off the dirt from the outside of the engine, especially the carb and linkages.

2. Use an after run at the end of the day. Since fuel contains elements that are hydroscopic (they abosrb water), any fuel left in an engine will attract moisture and therefore contribute to rust. It is important that you run the engine dry after your last flight or run to remove the last of the raw fuel. This can be done by simply pulling the fuel line from the engine and letting the engine run out. Apply several drops of after run oil into your carb and turn the engine over to ensure the oil gets distributed throughout the inner workings, coating the metal and protecting it from rust.

3. Ensure all of your nuts and bolts are tight. Between flying or running sessions, check that all of your bolts, such as the head bolts, backplate bolts, muffler bolts, engine mounting bolts, and carb mounting screws, are tight. Also, check that prop nut to ensure you won't be launching a spinning prop on your next flight. An over revved engine, particularly a four stroke, can cause damage without the load of a prop or flywheel.

End of Season Maintenance

When the flying season is over, a small amount of engine care can ensure a successful beginning to the following season.

Remove your engine from the model and give it a visual check—essentially perform the same checks you would do at the end of a day. Make sure that all bolts are in place and tight. It is not necessary to disassemble the engine unless you feel that there is internal damage or that the bearings require replacing. Replace any stripped bolts or rough running bearings. Clean the entire engine with motor spray to remove all dirt. Finally, load up the engine with after run oil, turning it over to ensure that all moving internal parts are covered. This will go a long way to reducing the chance of your engine rusting in the off season. Store the engine in a baggie to keep the dirt out and the oil in!

Beginning of the Season

The first thing to do before re-installing your engine is to replace the plumbing in your model. Remove the fuel tank and take out the rubber stopper and all brass and silicone tubing. There are components in the fuel that break down brass over time and if left, the tubing will eventually crumble or at the least allow air to enter the line. Clean the residue from the tank itself with a bit of isopropyl alcohol and then install a new rubber stopper assembly with new brass and silicone tubing. Reinstall your tank.

Take your engine from its baggie and use spray motor cleaner to get the after run off the outside of the casing. Re-install your engine to the model. When you are ready to run your engine, remove the glow plug and flush fresh fuel through the engine, turning it over with your thumb over the carb. This will clear out the storage oil. Replace the plug and start your engine as normal.

In Case of a Crash

We all hate to consider the possibility, but crashes are inevitable and the more we can salvage from them, the better. Quite often the engine can fair well in a crash unless your model has gone headlong into a rock or pavement.

Crashing on land will most certainly leave the engine dirty, inside and out. DO NOT TURN YOUR ENGINE OVER! Damage to the internal workings could result from the ingested grit. It is important to disassemble the engine as soon as possible because raw fuel will be in the crankcase which will create rust damage if the engine is left any length of time. For more detailed information on engine disassembly, please refer to the various publications on model engines.

Clean all of the parts with your motor spray. Inspect each component for breakage or wear. This is as good a time as any to replace any worn parts. Once you are satisfied that everything is clean and all components are serviceable, reassemble the engine.